Ryota SAKAMOTO Koichi TANNO Hiroki TAMURA
In this letter, we describe a low power current to time converter for wireless sensor networks. The proposed circuit has some advantages of high linearity and wide measurement range. From the evaluation using HSPICE with 0.18 µm CMOS device parameters, the output differential error for the input current variation is approximately 0.1 µs/nA under the condition that the current is varied from 100 nA to 500 nA. The idle power consumption is approximately zero.
Zheng TANG Takayuki YAMAGUCHI Koichi TASHIMA Okihiko ISHIZUKA Koichi TANNO
This paper describes a new model of multiple-valued immune network based on biological immune response network. The model of multiple-valued immune network is formulated based on the analogy with the interaction between B cells and T cells in immune system. The model has a property that resembles immune response quite well. The immunity of the network is simulated and makes several experimentally testable predictions. Simulation results are given to a letter recognition application of the network and compared with binary ones. The simulations show that, beside the advantages of less categories, improved memory pattern and good memory capacity, the multiple-valued immune network produces a stronger noise immunity than binary one.
Motoi INABA Koichi TANNO Hiroki TAMURA Okihiko ISHIZUKA
In this paper, optimization and verification of the current-mode multiple-valued digit ORNS arithmetic circuits are presented. The multiple-valued digit ORNS is the redundant number system using digit values in the multiple-valued logic and it realizes the full-parallel calculation without any ripple carry propagation. First, the 4-bit addition and multiplication algorithms employing the multiple-valued digit ORNS are optimized through logic-level analyses. In the multiplier, the maximum digit value and the number of modulo operations in series are successfully reduced from 49 to 29 and from 3 to 2, respectively, by the arrangement of addition lines. Next, circuit components such as a current mirror are verified using HSPICE. The proposed switched current mirror which has functions of a current mirror and an analog switch is effective to reduce the minimum operation voltage by about 0.13 volt. Besides an ordinary strong-inversion region, the circuit components operated under the weak-inversion region show good simulation results with the unit current of 10 nanoamperes, and it brings both of the lower power dissipation and the stable operation under the lower supply voltage.
Makoto SYUTO Eriko SATAKE Koichi TANNO Okihiko ISHIZUKA
In this letter, we propose high-speed binary to residue converters for moduli 2n, 2n 1 without using look-up table. For integration of residue arithmetic circuit using a signed-digit (SD) number representation with ordinary binary system, the proposed circuits carry out the efficient conversion. Using SD adders instead of ordinary adders that are used in conventional binary to residue converter, the high-speed conversion without the carry propagation can be achieved. Thus, the proposed converter is independent of the size of modulus and can speed up the binary to residue conversion. On the simulation, the conversion delay times are 1.78 ns for modulus 210-1 and 1.73 ns for modulus 210+1 under the condition of 0.6 µm CMOS technology, respectively. The active area of the proposed converter for moduli 210 1 is 335 µm325 µm.
Jing SHEN Koichi TANNO Okihiko ISHIZUKA Zheng TANG
A neuron-MOS transistor (νMOS) is applied to current-mode multi-valued logic (MVL) circuits. First, a novel low-voltage and low-power νMOS current mirror is presented. Then, a threshold detector and a quaternary T-gate using the proposed νMOS current mirrors are proposed. The minimum output voltage of the νMOS current mirror is decreased by VT (threshold voltage), compared with the conventional double cascode current mirror. The νMOS threshold detector is built on a νMOS current comparator originally composed of νMOS current mirrors. It has a high output swing and sharp transfer characteristics. The gradient of the proposed comparator output in the transfer region can be increased 6.3-fold compared with that in the conventional comparator. Along with improved operation of the novel current comparator, the discriminative ability of the proposed νMOS threshold detector is also increased. The performances of the proposed circuits are validated by HSPICE with Motorola 1.5 µm CMOS device parameters. Furthermore, the operation of a νMOS current mirror is also confirmed through experiments on test chips fabricated by VDEC*. The active area of the proposed νMOS current mirror is 63 µm 51 µm.
In this paper, we propose a midpoint-validation method which improves the generalization of Support Vector Machine. The proposed method creates midpoint data, as well as a turning adjustment parameter of Support Vector Machine using midpoint data and previous training data. We compare its performance with the original Support Vector Machine, Multilayer Perceptron, Radial Basis Function Neural Network and also tested our proposed method on several benchmark problems. The results obtained from the simulation shows the effectiveness of the proposed method.
Koichi TANNO Kiminobu SATO Hisashi TANAKA Okihiko ISHIZUKA
In this letter, we propose a sample and hold circuit (S/H circuit) with the clock boost technique and the input signal tracking technique. The proposed circuit block generates the clock with the amplitude of VDD + vin, and the clock is used to control the MOS switch. By applying this circuit to a S/H circuit, we can deal with the rail-to-rail signal with maintaining low distortion. Furthermore, the hold error caused by the charge injection and the clock feedthrough can be also reduced by using the dummy switch. The Star-HSPICE simulation results are reported in this letter.
Mingmin YAN Hiroki TAMURA Koichi TANNO
The aim of this study is to present electrooculogram signals that can be used for human computer interface efficiently. Establishing an efficient alternative channel for communication without overt speech and hand movements is important to increase the quality of life for patients suffering from Amyotrophic Lateral Sclerosis or other illnesses that prevent correct limb and facial muscular responses. In this paper, we introduce the gaze estimation system of electrooculogram signals. Using this system, the electrooculogram signals can be recorded when the patients focused on each direct. All these recorded signals could be analyzed using math-method and the mathematical model will be set up. Gaze estimation can be recognized using electrooculogram signals follow these models.
Zheng TANG Yuichi SHIRATA Okihiko ISHIZUKA Koichi TANNO
A calibrating analog-to digital (A/D) converter employing a T-Model neural network is described. The T-Model neural-based A/D converter architecure is presented with particular emphasis on the elimination of local minimum of the Hopfield neural network. Furthermore, a teacher forcing algorithm is presented and used to synthesize the A/D converter and correct errors of the converter due to offset and device mismatch. An experimental A/D converter using standard 5-µm CMOS discrete IC circuits demonstrates high-performance analog-to-digital conversion and calibrating.
Koichi TANNO Okihiko ISHIZUKA Zhen TANG
This paper describes a novel input-free MOS VT extractor circuit. The circuit consists of a bias voltage block and a novel VT extractor block. The proposed VT extractor block has the advantages of the ground-referenced output, low influence of the nonideality, few numbers of transistors and no influence of the PMOS process. The PSpice simulations show the supply voltage range and the bias voltage range of the proposed circuit are wider than those of Johnson's or Wang's.
Muneo KUSHIMA Koichi TANNO Okihiko ISHIZUKA
In this paper, a voltage-controlled linear variable resistor (VCLVR) using a floating-gate MOSFET (FG-MOSFET) is proposed. First, the grounded VCLVR realization is discussed. The proposed circuit consists of only an ordinary MOSFET and an FG-MOSFET. The advantages of the proposed VCLVR are low-power and wide-input range and also the power consumption of the proposed VCLVR is the same as an ordinary passive resistor. The performance of the proposed circuits are confirmed by HSPICE simulations with a standard 0.6 µm CMOS process parameters. Simulations of the proposed VCLVR demonstrate a resistance value of 40 kΩ to 338 kΩ and an input range of 4.34 V within THD of less than 1.1%. Next, we proposed a new floating node linear variable resistor using the proposed VCLVR. The performance of the circuit is also evaluated through HSPICE.
Koichi TANNO Okihiko ISHIZUKA Zheng TANG
In this paper, a four-quadrant analog multiplier consisting of four neuron-MOS transistors and two load resistors is proposed. The proposed multiplier can be operated at only 1 V. Furthermore, the input range of the multiplier is equal to 100% of the supply voltage. The theoretical harmonic distortion caused by mobility degradation and device mismatchs is derived in detail. The performance of the proposed multiplier is characterized through HSPICE simulations with a standard 2.0 µm CMOS process with a double-poly layer. Simulations of the proposed multiplier demonstrate that the linearity error of 0.77% and a total harmonic distortion of 0.62% are obtained with full-scale input conditions. The maximum power consumption and 3 dB bandwidth are 9.56 µW and 107 MHz, respectively. The active area of the proposed multiplier is 210 µm 140 µm.
Muneo KUSHIMA Motoi INABA Koichi TANNO
In this letter, my proposals for a Floating node voltage-controlled Variable Resistor circuit (FVR) are based upon its advantages as linear and compact. The performance of the proposed circuit was confirmed by PSpice simulation. The simulation results are reported in this letter.
Kenya KONDO Hiroki TAMURA Koichi TANNO
In this paper, we propose the low voltage CMOS current mode reference circuit using self-regulator with adaptive biasing technique. It drastically reduces the line sensitivity (LS) of the output voltage and the power supply voltage dependence of the temperature coefficient (TC). The self-regulator used in the proposed circuit adaptively generates the minimum voltage required the reference core circuit following the PVT (process, voltage and temperature) conditions. It makes possible to improve circuit performances instead of slightly increasing minimum power supply voltage. This proposed circuit has been designed and evaluated by SPICE simulation using TSMC 65nm CMOS process with 3.3V (2.5V over-drive) transistor option. From simulation results, LS is reduced to 0.0065%/V under 0.8V < VDD < 3.0V. TC is 67.6ppm/°C under the condition that the temperature range is from -40°C to 125°C and VDD range is from 0.8V to 3.0V. The power supply rejection ratio (PSRR) is less than -80.4dB when VDD is higher than 0.8V and the noise frequency is 100Hz. According to the simulation results, we could confirm that the performances of the proposed circuit are improved compared with the conventional circuit.
Koichi TANNO Okihiko ISHIZUKA Zheng TANG
This paper describes an N-type and a P-type MOS cascode circuit based on the square-law characteristics of an MOS transistor in saturation region. The transconductance parameter ratios of an upper and a lower MOS transistor are set to be 1: n2 for the N-type MOS cascode circuit and n2: 1 for the P-type MOS cascode circuit. The N and P-type MOS cascode circuits are divided to four types by the difference of connections of input terminals. We consider the input-output relations of each type circuit. The second-order effects of the circuit such as channel length modulation effect, mobility reduction effect and device mismatch are analyzed. As applications, an analog voltage adder and a VT level shifter using MOS cascode circuits are presented. All of the proposed circuits are very simple and consist of only the N and P-type MOS cascode circuits. The proposed circuits aer confirmed by SPICE simulation with MOSIS 1.2µm CMOS process parameters.
Motoi INABA Koichi TANNO Okihiko ISHIZUKA
The analog inverter for realization of the NOT function is the indispensable circuit element in the voltage-mode analog and digital signal processing. In this paper, we propose a novel analog inverter composed of only two neuron-MOS transistors. The analog inverter has the weighted negative feedback mechanism to operate both of neuron-MOS transistors under the saturation region in all input ranges. In verification using HSPICE simulations, the analog inverter performs the high linearity with errors of approximately 40 [mV] in all input ranges, particularly errors of less than 19 [mV] in more than 90% of input ranges. And, the maximum power consumption of the analog inverter is less than 1.5 [µW] although a peak of a standard CMOS inverter is around 30 [µW] under the supply voltage of 3.0 [V]. These good stability and results are produced by the negative feedback. Furthermore, fabrication costs of the analog inverters can be kept at the minimum because neuron-MOS transistors can be actualized in a conventional CMOS process without any additional process. For applications of the analog inverter, the voltage comparator with high noise margins is designed and is applied to the two-input MAX and the two-input MIN circuits in the voltage-mode. The MAX and the MIN circuits for realization of the MAX and the MIN functions, respectively, can be composed of total ten transistors each. They also perform well in verifications. On the basis of the proposed circuits, almost all of voltage-mode multi-valued logic circuits with high-performance can be realized like present binary logic systems. And, the proposed circuits can give full play to the high linearity and advantages for the arbitrary transformation of signal forms in the analog signal processing such as the fuzzy control.
Ryoichi MIYAUCHI Akio YOSHIDA Shuya NAKANO Hiroki TAMURA Koichi TANNO Yutaka FUKUCHI Yukio KAWAMURA Yuki KODAMA Yuichi SEKIYA
This paper describes the Fractional-N All Digital Frequency Locked Loop (ADFLL) with Robustness for PVT variation and its application for the microcontroller unit. The conventional FLL is difficult to achieve the required specification by using the fine CMOS process. Especially, the conventional FLL has some problems such as unexpected operation and long lock time that are caused by PVT variation. To overcome these problems, we propose a new ADFLL which uses dynamic selecting digital filter coefficients. The proposed ADFLL was evaluatied through the HSPICE simulation and fabricating chips using a 0.13 µm CMOS process. From these results, we observed the proposed ADFLL has robustness for PVT variation by using dynamic selecting digital filter coefficient, and the lock time is improved up to 57%, clock jitter is 0.85 nsec.
Koichi TANNO Jing SHEN Okihiko ISHIZUKA Zheng TANG
In this paper, a threshold voltage (VT) cancellation circuit for neuron-MOS (νMOS) analog circuits is described. By connecting the output terminal of this circuit with one of the input terminals of the νMOS transistor, cancellation ofVT is realized. The circuit has advantages of ground-referenced output and is insensitive to the fluctuation of bias and supply voltages. Second-order effects, such as the channel length modulation effect, the mobility reduction effect and device mismatch of the proposed circuit are analyzed in detail. Low-power and high-swing νMOS cascode current mirror is presented as an application. Performance of the proposed circuits is confirmed by HSPICE simulation with MOSIS 2. 0 µ p-well double-poly and double-metal CMOS device parameters.
Kenya KONDO Koichi TANNO Hiroki TAMURA Shigetoshi NAKATAKE
In this paper, we propose the novel low voltage CMOS current mode reference circuit. It reduces the minimum supply voltage by consisting the subthreshold two stage operational amplifier (OPAMP) which is regarded as the combination of the proportional to absolute temperature (PTAT) and the complementary to absolute temperature (CTAT) current generators. It makes possible to implement without extra OPAMP. This proposed circuit has been designed and evaluated by SPICE simulation using TSMC 65nm CMOS process with 3.3V (2.5V over-drive) transistor option. From simulation results, the line sensitivity is as good as 0.196%/V under the condition that the range of supply voltage (VDD) is wide as 0.6V to 3.0V. The temperature coefficient is 71ppm/ under the condition that the temperature range is from -40 to 125 and VDD=0.6V. The power supply rejection ratio (PSRR) is -47.7dB when VDD=0.6V and the noise frequency is 100Hz. According to comparing the proposed circuit with prior current mode circuits, we could confirm the performance of the proposed circuit is better than that of prior circuits.
Zheng TANG Yasuyoshi KOBAYASHI Okihiko ISHIZUKA Koichi TANNO
In this paper, we propose a learning fuzzy network (LFN) which can be used to implement most of fuzzy logic functions and is much available for hardware implementations. A learning algorithm largely borrowed from back propagation algorithm is introduced and used to train the LFN systems for several typical fuzzy logic problems. We also demonstrate the availability of the LFN hardware implementations by realizing them with CMOS current-mode circuits and the capability of the LFN systems by testing them on a benchmark problem in intelligent control-the inverted pendulum system. Simulations show that a learning fuzzy network can be realized with the proposed LFN system, learning algorithm, and hardware implementations.